Hi-Fi 4 Sale - Malaysia / Singapore Audio Forum & Marketplace | www.hifi4sale.net
Would you like to react to this message? Create an account in a few clicks or log in to continue.




Search
 
 

Display results as :
 


Rechercher Advanced Search

440Hz.my - expanding musical horizons
Subscribe to our Feed
addtomyyahoo4 Subscribe with BloglinesAdd to netvibes
Add to Google

Accustic Art Power Cord Ferrite II 2.0m

Go down

Accustic Art Power Cord Ferrite II 2.0m Empty Accustic Art Power Cord Ferrite II 2.0m

Post by tongho Thu Aug 25, 2022 6:48 am

Selling beloved Accustic Art POwer Cord Ferrite II 2.0m RM1780.00

https://wa.me/60122738893

  • Pure copper strand (99.999 % OFC) with Ferrite-Compound absorbing layer and high quality EMC shielding foil

  • Premium quality mains plug: extremely stable housing; very elaborate and massive contact pin

  • Premium quality IEC-plug: special audiophile plug from WATTGATE:registered:; very elaborate contact surfaces for very stable fit

  • Cross section: 3 x 2.5 mm2

  • Outside cord diameter: 14 mm

  • Standard length: 2 m – fully assembled / additional lengths per 0.5 m add-on

  • Available with European mains plug and US mains plug (WATTGATE:registered:)

  • All ACCUSTIC ARTS:registered: cables are “Handmade in Germany“





POWER CORD-FERRITE II (2.0M)
Principal Design
The cables of the ACCUSTIC ARTS? POWER CORD series are of a very
elaborate design and, in many ways, extremely different from standard
power cords. Power cords, when connecting electronic devices, play a
very big role in the transmission of power line noise, which can cause
distortion to audio signals. To avoid these phenomena, there are quite a
few steps that can be taken, for example: shielding.
Shielding is not only being used under the outer covering of the
ACCUSTIC ARTS? POWER CORD FERRITE II but additionally, each of the
three copper conductors are shielded with a very elaborate ?Ferrite-Compound?
covering. Due to this absorbing layer over the copper conductor,
the power cord acts like a ?low pass?-filter without influencing the low
frequency music signal.
High frequencies are absorbed by the magnetical and dielectrical loss of
the ?Ferrite-Compound? covering and transformed into heat. The damping
is proportional to the length of the cord.



Accustic Art Power Cord Ferrite II 2.0m Whats249
Accustic Art Power Cord Ferrite II 2.0m Whats250

tongho
Frequent Contributor
Frequent Contributor

Number of posts : 511
Age : 39
Location : KL
Registration date : 2014-03-04

Character sheet
Source(s): VPI Prime, Audia Flight Phono, SoulNote sc710
Amplification: Accuphase E470
Speakers: Quad z3

Back to top Go down

Accustic Art Power Cord Ferrite II 2.0m Empty Re: Accustic Art Power Cord Ferrite II 2.0m

Post by tongho Wed Sep 07, 2022 2:46 am

Bump

tongho
Frequent Contributor
Frequent Contributor

Number of posts : 511
Age : 39
Location : KL
Registration date : 2014-03-04

Character sheet
Source(s): VPI Prime, Audia Flight Phono, SoulNote sc710
Amplification: Accuphase E470
Speakers: Quad z3

Back to top Go down

Accustic Art Power Cord Ferrite II 2.0m Empty Re: Accustic Art Power Cord Ferrite II 2.0m

Post by tongho Wed Sep 21, 2022 5:05 pm

bump

tongho
Frequent Contributor
Frequent Contributor

Number of posts : 511
Age : 39
Location : KL
Registration date : 2014-03-04

Character sheet
Source(s): VPI Prime, Audia Flight Phono, SoulNote sc710
Amplification: Accuphase E470
Speakers: Quad z3

Back to top Go down

Accustic Art Power Cord Ferrite II 2.0m Empty Re: Accustic Art Power Cord Ferrite II 2.0m

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum